Dexamethasone Topical Aerosol
» Dexamethasone Topical Aerosol is Dexamethasone in a suitable lotion base mixed with suitable propellants in a pressurized container. Dexamethasone Topical Aerosol delivers not less than 90.0 percent and not more than 120.0 percent of the labeled amount of C22H29FO5.
Packaging and storage— Preserve in pressurized containers, and avoid exposure to excessive heat.
USP Reference standards 11
USP Dexamethasone RS Click to View Structure
Identification— Evaporate 5 mL of the Assay preparation, obtained as directed in the Assay, on a steam bath just to dryness, and dissolve the residue in 1 mL of chloroform. Apply 100 µL of this solution and 10 µL of a solution of USP Dexamethasone RS in chloroform containing 500 µg per mL to a suitable thin-layer chromatographic plate (see Chromatography 621) coated with a 0.25-mm layer of chromatographic silica gel. Allow the spots to dry, and develop the chromatogram in a solvent system consisting of a mixture of chloroform and diethylamine (2:1) until the solvent front has moved about three-fourths of the length of the plate. Remove the plate from the developing chamber, mark the solvent front, and allow the solvent to evaporate. Locate the spots on the plate by lightly spraying with dilute sulfuric acid (1 in 2) and heating on a hot plate or under a heat lamp until spots appear: the RF value of the principal spot obtained from the test solution corresponds to that obtained from the Standard solution.
Microbial enumeration tests 61 and Tests for specified microorganisms 62 It meets the requirements of the tests for absence of Staphylococcus aureus and Pseudomonas aeruginosa.
Other requirements— It meets the requirements for Pressure Test, Minimum Fill, and Leakage Test under Aerosols, Nasal Sprays, Metered-Dose Inhalers, and Dry Powder Inhalers 601.
Assay—
Standard preparation— Prepare as directed under Assay for Steroids 351, using USP Dexamethasone RS.
Assay preparation— Shake the Topical Aerosol container gently, and invert, immersing the valve in about 75 mL of alcohol contained in a 400-mL beaker. Actuate the valve by pushing against the bottom of the beaker. Remove the container at 15-second intervals, shake gently, and allow the container to warm to room temperature. Continue spraying until the contents of the container are exhausted. Transfer the alcohol solution to a 100-mL volumetric flask, dilute with alcohol to volume, and mix. Dilute an accurately measured volume of this solution, equivalent to about 1 mg of dexamethasone, with alcohol to 100.0 mL, and mix. Transfer 20.0 mL of this solution to a glass-stoppered, 50-mL flask.
Procedure— Proceed as directed for Procedure under Assay for Steroids 351, except to allow to stand in the dark for 45 minutes. Calculate the quantity, in mg, of C22H29FO5 in each container taken by the formula:
(10C / V)(AU / AS)
in which V is the volume, in mL, of assay solution taken for the second dilution.
Auxiliary Information— Please check for your question in the FAQs before contacting USP.
Topic/Question Contact Expert Committee
Monograph Domenick Vicchio, Ph.D.
Senior Scientific Liaison
1-301-998-6828
(SM42010) Monographs - Small Molecules 4
Reference Standards RS Technical Services
1-301-816-8129
rstech@usp.org
61 Radhakrishna S Tirumalai, Ph.D.
Principal Scientific Liaison
1-301-816-8339
(GCM2010) General Chapters - Microbiology
62 Radhakrishna S Tirumalai, Ph.D.
Principal Scientific Liaison
1-301-816-8339
(GCM2010) General Chapters - Microbiology
USP35–NF30 Page 2836