Mometasone Furoate Cream
DEFINITION
Mometasone Furoate Cream is Mometasone Furoate in a suitable cream base. It contains NLT 90.0% and NMT 110.0% of the labeled amount of mometasone furoate (C27H30Cl2O6).
IDENTIFICATION
• A.
The retention time of the major peak of the Sample solution corresponds to that of the Standard solution, both relative to the internal standard, as obtained in the Assay.
• B. Thin-Layer Chromatographic Identification Test 201
Standard solution:
0.2 mg/mL of USP Mometasone Furoate RS in acetonitrile
Sample solution:
0.2 mg/mL of mometasone furoate from Cream in acetonitrile
Developing solvent system:
Chloroform and ethyl acetate (3:1)
Acceptance criteria:
The RF value of the principal spot of the Sample solution corresponds to that of the Standard solution.
ASSAY
• Procedure
[NoteProtect from light. ]
Diluent A:
Tetrahydrofuran and glacial acetic acid (100:1)
Diluent B:
Acetonitrile, water, and glacial acetic acid (50:50:1)
Solution A:
Water
Solution B:
Acetonitrile
Mobile phase:
See Table 1.
Table 1
Internal standard solution:
1.4 mg/mL of diethyl phthalate in acetonitrile
Standard stock solution:
0.2 mg/mL of USP Mometasone Furoate RS in Diluent A
Standard solution:
0.05 mg/mL of mometasone furoate and 0.35 mg/mL of diethyl phthalate from equal quantities of the Standard stock solution and the Internal standard solution, in Diluent B
Sample solution:
Transfer a portion of Cream, equivalent to 1.0 mg of mometasone furoate, to a 50-mL, screw-capped centrifuge tube. Add 5.0 mL of Diluent A and a few glass beads, and mix on a vortex mixer. Add 5.0 mL of Internal standard solution, and mix. Add 10.0 mL of Diluent B, mix on a vortex mixer for 1 min, and centrifuge for 10 min. Pass the aqueous phase through a polypropylene filter of 0.2-µm pore size, discarding the first 12 mL of filtrate.
Chromatographic system
Mode:
LC
Detector:
UV 254 nm
Column:
4.6-mm × 25-cm; 5-µm packing L60
Flow rate:
2 mL/min
Injection size:
20 µL
System suitability
Sample:
Standard solution
[NoteThe relative retention times for diethyl phthalate and mometasone furoate are 0.4 and 1.0, respectively. ]
Suitability requirements
Tailing factor:
NMT 1.5 for the mometasone furoate peak
Relative standard deviation:
NMT 2.0%
Analysis
Samples:
Standard solution and Sample solution
Calculate the percentage of mometasone furoate (C27H30Cl2O6) in the portion of Cream taken:
Result = (RU/RS) × (CS/CU) × 100
Acceptance criteria:
90.0%110.0%
PERFORMANCE TESTS
• Minimum Fill 755:
Meets the requirements
IMPURITIES
• Organic Impurities
[NoteProtect from light. ]
Diluent A, Solution A, Solution B, Mobile phase, and Standard stock solution:
Prepare as directed in the Assay.
Diluent C:
Acetonitrile, water, and glacial acetic acid (30:70:1)
System suitability solution:
0.1 µg/mL of USP Mometasone Furoate RS from Standard stock solution in Diluent C
Blank solution:
Diluent C and Diluent A (3:1)
Sample solution:
Transfer a portion of Cream, equivalent to 2.0 mg of mometasone furoate, to a 50-mL, screw-capped centrifuge tube. Add 5.0 mL of Diluent A and a few glass beads, and mix on a vortex mixer. Add 15.0 mL of Diluent C, and mix. Centrifuge for 10 min. Pass the aqueous phase through a 0.2-µm polypropylene filter, discarding the first 12 mL of filtrate.
Chromatographic system
Mode:
LC
Detector:
UV 254 nm
Column:
4.6-mm × 25-cm; 5-µm packing L60
Column temperature:
25 ± 5
Flow rate:
2 mL/min
Injection size:
50 µL
System suitability
Sample:
System suitability solution
Suitability requirements
Relative standard deviation:
NMT 10%
Analysis
Samples:
System suitability solution, Blank solution, and Sample solution
[NoteExclude any peak areas less than those from the System suitability solution. Also exclude any peaks with the same retention time as that observed in the Blank solution. Any peaks having a relative retention time of about 1.04 or 1.13 are controlled in the Mometasone Furoate monograph and, therefore, are not included in the total specified and unspecified impurities limit. ]
Calculate the percentage of each impurity in the portion of Cream taken:
Result = (rU/rT) × 100
Acceptance criteria:
See Table 2.
Table 2
SPECIFIC TESTS
• Microbial Enumeration Tests 61 and Tests for Specified Microorganisms 62:
It meets the requirements of the tests for absence of Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli, and Salmonella species.
ADDITIONAL REQUIREMENTS
• Packaging and Storage:
Preserve in well-closed containers, and store at controlled room temperature.
Auxiliary Information
Please check for your question in the FAQs before contacting USP.
USP35NF30 Page 3944
Pharmacopeial Forum: Volume No. 35(1) Page 82
|