Apraclonidine Ophthalmic Solution
» Apraclonidine Ophthalmic Solution is a sterile, aqueous solution of Apraclonidine Hydrochloride. It contains an amount of apraclonidine hydrochloride (C9H10Cl2N4·HCl) equivalent to not less than 90.0 percent and not more than 115.0 percent of the labeled amount of apraclonidine (C9H10Cl2N4).
Packaging and storage Preserve in tight, light-resistant containers.
A: The retention time of the major peak in the chromatogram of the Assay preparation corresponds to that of the major peak in the chromatogram of the Standard preparation, as obtained in the Assay.
B: Apply 2 µL of Apraclonidine Ophthalmic Solution and 2 µL of a Standard solution of USP Apraclonidine Hydrochloride RS in methanol containing about 11.5 mg per mL to a suitable high performance thin-layer chromatographic plate (see Chromatography 621) coated with a 0.2-mm layer of chromatographic silica gel mixture, or equivalent. Allow the applications to dry, and develop the chromatogram in a solvent system consisting of a mixture of chloroform, methanol, and ammonium hydroxide (74:22:4) until the solvent front has moved about three-fourths of the length of the plate. Remove the plate from the developing chamber, mark the solvent front, and allow the solvent to evaporate. Locate the spots on the plate by viewing under short-wavelength UV light. [noteThe apraclonidine spot should appear as a blue spot.] Spray the plate with fluorescamine solution, prepared by dissolving about 25 mg of fluorescamine in 25 mL of acetone. [noteAvoid prolonged or repeated breathing of the aerosol from the fluorescamine spray. Also avoid prolonged or repeated contact with skin. Fluorescamine solution should be sprayed only in a hood.] Examine the plate under normal light and long-wavelength UV light. [noteThe apraclonidine spot should appear as a yellow spot under normal light and as a white spot under long-wavelength UV light.] The RF value and appearance of the principal spot obtained from the test solution corresponds to that obtained from the Standard solution.
Sterility 71 It meets the requirements when tested as directed for Membrane Filtration under Test for Sterility of the Product to be Examined.
pH 791: between 4.4 and 7.8.
Phosphate buffer Prepare as directed in the test for Chromatographic purity under Apraclonidine Hydrochloride.
Mobile phase Prepare a filtered and degassed mixture of Phosphate buffer, acetonitrile, and methanol (68:30:2). Make adjustments if necessary (see System Suitability under Chromatography 621).
Standard preparation Dissolve an accurately weighed quantity of USP Apraclonidine Hydrochloride RS in water, and dilute quantitatively, and stepwise if necessary, with water to obtain a Stock standard solution having a known concentration of about 0.23 mg per mL. Transfer 2.5 mL of this solution to a 50-mL volumetric flask, dilute with Mobile phase to volume, and mix to obtain a Standard preparation having a known concentration of about 11.5 µg of USP Apraclonidine Hydrochloride RS per mL (equivalent to about 10 µg of apraclonidine per mL).
Resolution solution Transfer about 1 mL of propiophenone to a 100-mL volumetric flask, dilute with methanol to volume, and mix. Transfer 3.0 mL of this solution to a 50-mL volumetric flask, dilute with methanol to volume, and mix. Transfer 1.0 mL of this solution and 5.0 mL of the Stock standard solution to a 100-mL volumetric flask, dilute with Mobile phase to volume, and mix.
Assay preparation Transfer an accurately measured volume of Ophthalmic Solution, equivalent to about 20 mg of apraclonidine, to a 100-mL volumetric flask, dilute with water to volume, and mix. Transfer 2.5 mL of this solution to a 50-mL volumetric flask, dilute with Mobile phase to volume, and mix.
Chromatographic system (see Chromatography 621)The liquid chromatograph is equipped with a 254-nm detector and an 8-mm × 100-mm column that contains packing L7. The flow rate is about 3 mL per minute. Chromatograph the Resolution solution, and record the peak responses as directed for Procedure: the relative retention times are about 0.6 for apraclonidine and 1.0 for propiophenone; the column efficiency determined from the analyte peak is not less than 1000 theoretical plates; the tailing factor for the analyte peak is not more than 2.2; the resolution, R, between the analyte and propiophenone peaks is not less than 3.0; and the relative standard deviation for replicate injections is not more than 2.0%.
Procedure Separately inject equal volumes (about 20 µL) of the Standard preparation and the Assay preparation into the chromatograph, record the chromatograms, and measure the areas for the major peaks. Calculate the quantity, in mg, of apraclonidine (C9H10Cl2N4) in each mL of the Ophthalmic Solution taken by the formula:
(245.11 / 281.57)(2C / V)(rU / rS)in which 245.11 and 281.57 are the molecular weights of apraclonidine and apraclonidine hydrochloride, respectively; C is the concentration, in µg per mL, of USP Apraclonidine Hydrochloride RS in the Standard preparation; V is the volume, in mL, of Ophthalmic Solution taken; and rU and rS are the apraclonidine peak responses obtained from the Assay preparation and the Standard preparation, respectively.
Auxiliary Information Please check for your question in the FAQs before contacting USP.Chromatographic Column
USP32NF27 Page 1574
Chromatographic columns text is not derived from, and not part of, USP 32 or NF 27.