» Amiloxate contains not less than 95.0 percent and not more than 105.0 percent of C15H20O3.
Packaging and storage Preserve in tight containers.
B: Ultraviolet Absorption 197U
Solution: 5.0 µg per mL.
Absorptivities, calculated on the as-is basis, do not differ by more than 3.0%.
Specific gravity 841: between 1.037 and 1.041.
Refractive index 831: between 1.556 and 1.560 at 20.
Acidity Transfer 50 mL of alcohol to a suitable container, add 1 mL of phenolphthalein TS, and add sufficient 0.1 N sodium hydroxide to obtain a persistent pink color. Transfer 50 mL of this solution to a suitable container, add about 5.0 mL of Amiloxate, accurately measured, mix, and titrate with 0.1 N sodium hydroxide: not more than 0.2 mL of titrant per mL of Amiloxate is required for neutralization.
Test solution Use the Assay preparation.
Chromatographic system Proceed as directed in the Assay. To evaluate the system suitability requirements, use the Standard preparation prepared as directed in the Assay.
Procedure Inject a volume (about 1 µL) of the Test solution into the chromatograph, record the chromatogram, and measure all of the peak responses. Calculate the percentage of each impurity in the portion of Amiloxate taken by the formula:
100(ri / rs)in which ri is the peak response for each impurity; and rs is the sum of the responses of all the peaks: not more than 0.1% of any individual impurity is found; and not more than 2.0% of total impurities is found.
Standard preparation Dissolve an accurately weighed quantity of USP Amiloxate RS in tert-butyl methyl ether, and dilute quantitatively, and stepwise if necessary, with tert-butyl methyl ether to obtain a solution having a known concentration of about 20.0 mg per mL.
Assay preparation Transfer about 2.0 g of Amiloxate, accurately weighed, to a 100-mL volumetric flask, dilute with acetone to volume, and mix.
Chromatographic system (see Chromatography 621) The gas chromatograph is equipped with a flame-ionization detector and a 0.32-mm × 25-m column coated with a 0.1-µm film of G1. The carrier gas is helium, flowing at a rate of about 6 mL per minute. The chromatograph is programmed as follows. Initially the temperature of the column is equilibrated at 60, then the temperature is increased at a rate of 8 per minute to 240, and maintained at 240 for 10 minutes. The injection port temperature is maintained at 240, and the detector temperature is maintained at 260. Chromatograph the Standard preparation, and record the peak responses as directed for Procedure: the resolution, R, between the amiloxate peak and any other peak is not less than 1.0; and the relative standard deviation for replicate injections is not more than 2.0%.
Procedure Separately inject equal volumes (about 1 µL) of the Standard preparation and the Assay preparation into the chromatograph, record the chromatograms, and measure the responses for the major peaks. Calculate the quantity, in mg, of C15H20O3 in the portion of Amiloxate taken by the formula:
100C(rU / rS)in which C is the concentration, in mg per mL, of USP Amiloxate RS in the Standard preparation; and rU and rS are the peak responses obtained from the Assay preparation and the Standard preparation, respectively.
Auxiliary Information Please check for your question in the FAQs before contacting USP.Chromatographic Column
USP32NF27 Page 1513Pharmacopeial Forum: Volume No. 27(5) Page 3017
Chromatographic columns text is not derived from, and not part of, USP 32 or NF 27.