» Desoximetasone Cream is Desoximetasone in an emollient cream base. It contains not less than 90.0 percent and not more than 110.0 percent of the labeled amount of C22H29FO4.
Packaging and storage Preserve in collapsible tubes, at controlled room temperature.
Identification Evaporate 25 mL of the Assay preparation, prepared as directed in the Assay, on a steam bath just to dryness, and dissolve the residue in 2 mL of acetonitrile. This is the test solution. Prepare a Standard solution of USP Desoximetasone RS in acetonitrile containing 500 µg per mL. Using 10 µL instead of 20 µL of each solution, proceed as directed in Identification test B under Desoximetasone, beginning with Apply separately 20 µL of each. The specified result is observed.
Minimum fill 755: meets the requirements.
pH 791: between 4.0 and 8.0, in a solution prepared in the following manner. Add 15 mL of boiling water to 3.5 g of the Cream in a 50-mL centrifuge tube, cap the tube, shake vigorously until the cream is uniformly dispersed, then place the tube in a steam bath until the water and oil layers separate completely. Cool, separate the layers, and determine the pH of the aqueous phase.
Mobile phase Prepare a filtered and degassed mixture of methanol, water, and glacial acetic acid (65:35:1). Make adjustments if necessary (see System Suitability under Chromatography 621).
Internal standard solution Prepare a solution of ethylparaben in methanol having a concentration of about 0.04 mg per mL.
Standard preparation Dissolve an accurately weighed quantity of USP Desoximetasone RS in methanol to obtain a solution having a known concentration of about 0.4 mg per mL. Pipet 5 mL of this solution into a 50-mL centrifuge tube. Add 10.0 mL of Internal standard solution, dilute with methanol quantitatively to 40.0 mL, and mix to obtain the Standard preparation having a known concentration of about 0.05 mg per mL.
Assay preparation Transfer an accurately weighed amount of Cream, equivalent to about 2 mg of desoximetasone, to a 50-mL centrifuge tube, and add a few 3-mm glass beads. Add 10.0 mL of Internal standard solution and about 30 mL of methanol, and mix. Tightly cap the centrifuge tube, and immerse it for 10 minutes in a bath maintained at a temperature of 65. Remove the tube from the bath, and immediately vortex at high speed for 30 seconds. Return the tube to the hot water bath for 5 minutes, remove it from the bath, and immediately vortex for 30 seconds. Repeat the procedure one more time, then cool the tube in an ice-bath held at 10 until no further flocculent precipitation occurs. Centrifuge, and use the supernatant.
Chromatographic system (see Chromatography 621)The liquid chromatograph is equipped with a 254-nm detector and a 4.6-mm × 15-cm column that contains packing L7. The flow rate is about 1 mL per minute. Chromatograph the Standard preparation, and record the peak responses as directed for Procedure: the relative retention times are about 1 and 2 for ethylparaben and desoximetasone, respectively; the tailing factor for the analyte peak is not more than 2.0; the resolution, R, between the analyte and internal standard peaks is not less than 2.0; and the relative standard deviation for replicate injections is not more than 2.0%.
Procedure Separately inject equal volumes (about 10 µL) of the Standard preparation and the Assay preparation into the chromatograph, record the chromatograms, and measure the responses for the major peaks. Calculate the quantity, in mg, of C22H29FO4 in the portion of Cream taken by the formula:
40C(RU / RS)in which C is the concentration, in mg per mL, of USP Desoximetasone RS in the Standard preparation; and RU and RS are the peak response ratios obtained from the Assay preparation and the Standard preparation, respectively.
Auxiliary Information Please check for your question in the FAQs before contacting USP.Chromatographic Column
USP32NF27 Page 2079
Chromatographic columns text is not derived from, and not part of, USP 32 or NF 27.