Diltiazem Hydrochloride Oral Solution
» Diltiazem Hydrochloride Oral Solution contains not less than 90.0 percent and not more than 110.0 percent of the labeled amount of diltiazem hydrochloride (C22H26N2O4S·HCl). Prepare Diltiazem Hydrochloride Oral Solution, 12 mg per mL, as follows (see Pharmaceutical Compounding—Nonsterile Preparations 795. See also Diltiazem Hydrochloride Oral Suspension):
Diltiazem Hydrochloride powder 1.2 g
Vehicle for Oral Solution (regular or
sugar-free), NF, a sufficient quantity
to make 100 mL
Add Diltiazem Hydrochloride powder and about 10 mL of Vehicle to a mortar, and mix. Add the Vehicle in small portions almost to volume, and mix thoroughly after each addition. Transfer the contents of the mortar, stepwise and quantitatively, to a calibrated bottle. Add enough Vehicle to bring to final volume, and mix well.
Packaging and storage— Preserve in tight, light-resistant containers. Store at controlled room temperature, or in a cold place.
Labeling— Label it to state the beyond-use date.
USP Reference standards 11
USP Diltiazem Hydrochloride RS Click to View Structure
pH 791: between 3.7 and 4.7.
Beyond-use date: 60 days after the day on which it was compounded.
Buffer solution— Dissolve 1.16 g of d-10-camphorsulfonic acid in 1000 mL of 0.1 M sodium acetate, adjust this solution by the addition of 0.1 N sodium hydroxide to a pH of 6.2, and mix.
Mobile phase— Prepare a filtered and degassed mixture of acetonitrile, methanol, and Buffer solution (2:1:1). Make adjustments if necessary (see System Suitability under Chromatography 621).
Standard preparation— Dissolve USP Diltiazem Hydrochloride RS in Mobile phase to obtain a solution having a known concentration of 120 µg per mL.
Assay preparation— Agitate the container of Oral Solution for 30 minutes on a rotating mixer, remove a 5-mL sample, and store in a clear glass vial at –70 until analyzed. At the time of analysis remove the sample from the freezer, allow it to reach room temperature, and mix with a vortex mixer for 30 seconds. Pipet 1.0 mL of the sample solution to a 100-mL volumetric flask, and dilute with Mobile phase to volume.
Chromatographic system (see Chromatography 621)— The liquid chromatograph is equipped with a 240-nm detector and a 4.6-mm × 25-cm analytical column that contains 5-µm packing L1. The flow rate is about 1.5 mL per minute. Chromatograph the Standard preparation, and record the peak responses as directed for Procedure: the retention time is about 9.6 minutes; and the relative standard deviation for replicate injections is not more than 1.3%.
Procedure— Separately inject equal volumes (about 20 µL) of the Standard preparation and the Assay preparation into the chromatograph, record the chromatograms, and measure the responses for the major peaks. Calculate the quantity, in mg, of diltiazem hydrochloride (C22H26N2O4S·HCl) in the volume of Oral Solution taken by the formula:
100(C/V)(rU / rS)
in which C is the concentration, in µg per mL, of USP Diltiazem Hydrochloride RS in the Standard preparation; V is the volume, in mL, of Oral Solution taken; and rU and rS are the peak responses obtained from the Assay preparation and the Standard preparation, respectively.
Auxiliary Information— Please check for your question in the FAQs before contacting USP.
Topic/Question Contact Expert Committee
Monograph Jeanne H. Sun
Assistant Scientific Liaison
(CMP2010) Compounding
Reference Standards RS Technical Services
USP35–NF30 Page 2920
Pharmacopeial Forum: Volume No. 32(1) Page 79