Betadex
Add the following:
Click to View Image
(C6H10O5)7 1134.98
Beta Cyclodextrin [7585-39-9].
NF27
» Betadex is a nonreducing cyclic compound composed of seven alpha-(1-4) linked d-glucopyranosyl units. It contains not less than 98.0 percent and not more than 102.0 percent of (C6H10O5)7, calculated on the anhydrous basis.
Change to read:
Packaging and storage— Preserve in tight containers. No storage requirements specified.NF27
Color and clarity of solution— Dissolve 0.2 g in 20.0 mL of freshly boiled and cooled water: the resulting solution is clear and colorless.
Change to read:
Identification—
A: Infrared Absorption 197K: on undried specimen.
B: The retention time of the major peak in the chromatogram of the Assay preparation corresponds to that in the chromatogram of the Standard preparation, as obtained in the Assay.
C: It meets the requirements of the test for Specific rotation.NF27
D: Mix 0.2 g with 2 mL of iodine TS, warm in a water bath to dissolve the test specimen, and allow to stand at room temperature: a yellow-brown precipitate is formed.
Specific rotation 781S: between +160 and +164 (t = 20).
Test solution: 10 mg per mL, in water.
Change to read:
Microbial enumeration tests 61 and Tests for specified microorganisms 62 The total aerobic microbial count does not exceed 1000 cfu per g, and the total combined molds and yeasts count does not exceed 100 cfu per g. It meets the requirements of the tests for absence of Salmonella species and Escherichia coli.NF27
Add the following:
pH 791 Add 0.1 mL of a saturated solution of potassium chloride to 10 mL of Betadex aqueous solution (1 in 100). The pH of the solution is between 5.0 and 8.0.NF27
Water, Method I 921: not more than 14.0%.
Residue on ignition 281: not more than 0.1%.
Change to read:
Heavy metals, Method II 231: not more thanNF27 5 ppm.
Change to read:
Reducing sugars
Cupric solution— Dissolve 15 g of cupric sulfate in water to make 100 mL.
Tartrate solution— Dissolve 2.5 g of anhydrous sodium carbonate, 2.5 g of potassium sodium tartrate, 2.0 g of sodium bicarbonate, and 20 g of anhydrous sodium sulfate in water to make 100 mL.
Cupric-tartaric solution— Immediately before use, mix 1 part of Cupric solution with 25 parts of Tartrate solution.
Ammonium molybdate reagent— Mix 10 mL of a solution of disodium arsenate (6 in 100), 50 mL of a solution of ammonium molybdate (1 in 10), and 90 mL of diluted sulfuric acid, and dilute with water to 200 mL.
Test solution— Transfer an accurate quantity of Betadex, equivalent to 1.0 g to a 100-mL volumetric flask; dissolve in and dilute with water that has been previously boiled and cooled to room temperature, to volume; and mix. To 1 mL of this solution add 1 mL of Cupric-tartaric solution. Heat on a water bath for 10 minutes, then cool to room temperature. Add 10 mL of Ammonium molybdate reagent, and allow to stand for 15 minutes.
Standard stock solution— Prepare a solution having a known concentration of 20 mg per L for USP Dextrose RS, calculated on the anhydrous basis.
Standard solution— Prepare as directed for the Test solution, at the same time, except to use 1 mL of Standard stock solution in place of 1.0 g of anhydrous Betadex.
Procedure— Measure the absorbance of the Test solution and the Standard solution at the wavelength of maximum absorbance at 740 nm relative to that of water, with a suitable spectrophotometer. The absorbance of the Test solution is not greater than that of the Standard solution (0.2%).NF27
Add the following:
Light-absorbing impurities—
Test solution— Transfer an accurate quantity of Betadex, equivalent to 1.0 g on the anhydrous basis, to a 100-mL volumetric flask; dissolve in and dilute with water that has been previously boiled and cooled to room temperature, to volume; mix; and pass through a 0.2-µm filter.
Procedure— Determine the absorbance of the Test solution in a 1-cm cell with a suitable spectrophotometer, after correcting for the blank: between 230 nm and 350 nm, the absorbance is not greater than 0.10; and between 350 nm and 750 nm, the absorbance is not greater than 0.05.NF27
Add the following:
Related compounds—
Mobile phase and Chromatographic system— Prepare as directed in the Assay.
System suitability solution— Prepare as directed for System suitability preparation in the Assay.
Standard solution— Transfer 5.0 mL of the System suitability solution into a 50-mL volumetric flask, and dilute with water to volume.
Test solution— Use the Assay stock preparation, prepared as directed in the Assay.
Procedure— Separately inject equal volumes (about 50 µL) of the Standard solution and the Test solution into the chromatograph, record the chromatograms, and measure the responses for the major peaks. For the Test solution, the areas of any peaks corresponding to alfadex (alpha cyclodextrin) or to gamma cyclodextrin are not greater than half of the area of the corresponding peaks in the chromatogram of the Standard solution (0.25%); and the sum of the areas of all the peaks, excluding the principal peak, the peaks corresponding to alfadex or to gamma cyclodextrin, and artifact peaks, is not greater than the area of the peak corresponding to betadex (beta cyclodextrin) in the chromatogram of the Standard solution (0.5%).NF27
Change to read:
Assay—
Mobile phase— Prepare a filtered and degassed mixture of water and methanol (93:7). Make adjustments if necessary (see System Suitability under Chromatography 621).
System suitability preparation— Dissolve accurately weighed quantities of USP Alpha Cyclodextrin RS, USP Beta Cyclodextrin RS, and USP Gamma Cyclodextrin RS in water, and dilute if necessary, to obtain a solution having known concentrations of 0.5 mg of each per mL for USP Alpha Cyclodextrin RS and USP Beta Cyclodextrin RS, each calculated on the anhydrous basis, and 0.5 mg per mL for USP Gamma Cyclodextrin RS, calculated on the dried basis.
Standard preparation— Dissolve an accurately weighed quantity of USP Beta Cyclodextrin RS in water to obtain a solution having a known concentration of about 1.0 mg per mL, calculated on the anhydrous basis.
Assay stock preparation— Transfer 250 mg of Betadex, accurately weighed, to a 25-mL volumetric flask, and dissolve in water, with the aid of heat, if necessary. Cool, and dilute with water to volume.
Assay preparation— Transfer 5.0 mL of the Assay stock preparation to a 50-mL volumetric flask, and dilute with water to volume.
Chromatographic system (see Chromatography 621) The liquid chromatograph is equipped with a refractive index detector and a 4.6-mm × 15-cm column that contains 5-µm packing L1. The temperature for the refractive index detector is maintained at 40, and the temperature for the analytical column is maintained at 30. The flow rate is about 1.5 mL per minute. Chromatograph the System suitability preparation, and identify the components based on their relative retention times, which are 0.4, 0.5, and 1.0 for gamma cyclodextrin, alfadex, and betadex, respectively. Record the peak responses as directed for Procedure: the resolution, R, between the gamma cyclodextrin and alfadex peaks is not less than 1.5; the tailing factors for the three cyclodextrins are between 0.8 and 2.0; and the relative standard deviation for replicate injections is not more than 2.0%.
Procedure— Separately inject equal volumes (about 50 µL) of the Standard preparation and the Assay preparation into the chromatograph, record the chromatograms, and measure the responses for the major peaks. Calculate the percentage of (C6H10O5)7 in the portion of Betadex taken by the formula:
100(10) × (25){C / [W(1 – 0.01A)]}(rU / rS)
in which 10 is a dilution factor for preparing the Assay preparation from the Assay stock preparation; 25 is the volume, in mL, of the Assay stock preparation; C is the concentration, in mg per mL, of USP Beta Cyclodextrin RS in the Standard preparation; W is the weight, in mg, of Betadex taken to prepare the Assay stock preparation; A is the percentage of Water in the Betadex taken; and rU and rS are the peak responses obtained from the Assay preparation and the Standard preparation, respectively.NF27
Auxiliary Information— Please check for your question in the FAQs before contacting USP.
Topic/Question Contact Expert Committee
Monograph Hong Wang, Ph.D.
Scientist
1-301-816-8351
(EM205) Excipient Monographs 2
Reference Standards Lili Wang, Technical Services Scientist
1-301-816-8129
RSTech@usp.org
61 Radhakrishna S Tirumalai, Ph.D.
Senior Scientist
1-301-816-8339
(MSA05) Microbiology and Sterility Assurance
62 Radhakrishna S Tirumalai, Ph.D.
Senior Scientist
1-301-816-8339
(MSA05) Microbiology and Sterility Assurance
USP32–NF27 Page 1175
Pharmacopeial Forum: Volume No. 34(1) Page 127
Chromatographic Column—
Chromatographic columns text is not derived from, and not part of, USP 32 or NF 27.