Atropine Sulfate Injection
» Atropine Sulfate Injection is a sterile solution of Atropine Sulfate in Water for Injection. It contains not less than 93.0 percent and not more than 107.0 percent of the labeled amount of (C17H23NO3)2·H2SO4· H2O.
Packaging and storage Preserve in single-dose or in multiple-dose containers, preferably of Type I glass.
Identification (see Thin-Layer Chromatographic Identification Test 201)
Adsorbent: chromatographic silica gel.
Developing solvent: mixture of chloroform and diethylamine (9:1).
Test preparation Use undiluted. Apply 15 µL.
Detection reagent: potassium iodoplatinate TS.
Procedure Proceed as directed for Procedure under Thin-Layer Chromatographic Identification Test 201, the spots on the plate located by spraying with Detection reagent.
Bacterial endotoxins 85 It contains not more than 55.6 USP Endotoxin Units per mg of atropine sulfate.
pH 791: between 3.0 and 6.5.
Other requirements It meets the requirements under Injections 1.
Acetate buffer Prepare a solution in water containing in each L 0.05 mole of sodium acetate and 2.9 mL of glacial acetic acid.
Mobile phase Transfer 5.1 g of tetrabutylammonium hydrogen sulfate to a 1-L volumetric flask, add 50 mL of acetonitrile, and dilute with Acetate buffer to volume. Adjust with 5 N sodium hydroxide to a pH of 5.5 ± 0.1.
Standard preparation Dissolve an accurately weighed quantity of USP Atropine Sulfate RS in water, and dilute quantitatively with water to obtain a solution having a known concentration of about 80 µg per mL.
Assay preparation Transfer an accurately measured volume of Injection, equivalent to about 2 mg of atropine sulfate, to a 25-mL volumetric flask, dilute with water to volume, and mix.
Resolution solution Prepare a solution in water containing about 2.5 µg of p-hydroxybenzoic acid per mL. Dilute one volume of this solution with four volumes of the Standard preparation.
Chromatographic system (see Chromatography 621) The liquid chromatograph is equipped with a 254-nm detector and 30-cm × 3.9-mm column that contains packing L1. The flow rate is about 2 mL per minute. Chromatograph the Standard preparation, and record the peak responses as directed for Procedure: the relative standard deviation for replicate injections is not more than 1.5%. In a similar manner, chromatograph the Resolution solution: the retention time of p-hydroxybenzoic acid is about 1.6 relative to that of atropine, and the resolution, R, between the p-hydroxybenzoic acid and atropine peaks is not less than 2.2.
Procedure Separately inject equal volumes (about 100 µL) of the Standard preparation and the Assay preparation into the chromatograph, record the chromatograms, and measure the areas for the major peaks. Calculate the quantity, in mg, of (C17H23NO3)2·H2SO4·H2O in each mL of the Injection taken by the formula:
(694.85/676.83)(25C/V)(rU / rS)in which 694.85 and 676.83 are the molecular weights of atropine sulfate monohydrate and anhydrous atropine sulfate, respectively; C is the concentration, in mg per mL, of USP Atropine Sulfate RS in the Standard preparation; V is the volume, in mL, of Injection taken; and rU and rS are the peak responses obtained from the Assay preparation and the Standard preparation, respectively.
Auxiliary Information Please check for your question in the FAQs before contacting USP.Chromatographic Column
USP32NF27 Page 1605
Chromatographic columns text is not derived from, and not part of, USP 32 or NF 27.