Ciclopirox Olamine Cream
» Ciclopirox Olamine Cream contains not less than 90.0 percent and not more than 110.0 percent of the labeled amount of ciclopirox olamine (C12H17NO2·C2H7NO).
Packaging and storage Preserve in collapsible tubes, and store at controlled room temperature.
Identification Dilute 4 mL of the Assay preparation obtained as directed in the Assay with a mixture of methanol and 6.25 N sodium hydroxide (123:2) to make 100 mL: the UV absorption spectrum of the solution so obtained exhibits maxima and minima at the same wavelengths as that of a similar solution prepared from the Standard preparation obtained as directed in the Assay, concomitantly measured.
Minimum fill 755: meets the requirements.
pH 791 Add 15 mL of boiling water, previously adjusted with 0.1 N hydrochloric acid or 0.1 N sodium hydroxide to a pH of 6 to 7, to 3.5 g of Cream in a 50-mL centrifuge tube. Place a cap on the tube, and shake vigorously until an emulsion is formed. Loosen the cap, and heat the tube on a steam bath for 10 minutes. Allow to cool, centrifuge, and determine the pH of the aqueous phase: the pH is between 5.0 and 8.0.
Content of benzyl alcohol (if present)
Solvent mixture Mix chloroform and methanol (4:1).
Internal standard solution Prepare a solution of 1-nonyl alcohol in Solvent mixture containing about 1.75 mg per mL.
Standard preparation Dilute an accurately weighed quantity of USP Benzyl Alcohol RS, quantitatively and stepwise, with Solvent mixture to obtain a solution having a known concentration of about 2 mg per mL. Transfer 5.0 mL of this solution and 5.0 mL of Internal standard solution to a 50-mL volumetric flask, dilute with Solvent mixture to volume, and mix.
Test preparation Transfer 1.0 g of Cream to a 50-mL volumetric flask, add about 30 mL of Solvent mixture, and mix. Add 5.0 mL of Internal standard solution, dilute with Solvent mixture to volume, and mix to obtain a clear solution.
Chromatographic system (see Chromatography 621) The gas chromatograph is equipped with a flame-ionization detector and contains a 4-mm × 2-m glass column packed with 3% phase G3 on 100- to 120-mesh support S1AB. The column is maintained at a temperature of about 100, the injection port and detector temperatures are maintained at about 315, and nitrogen is used as the carrier gas at a flow rate of about 45 mL per minute. Chromatograph the Standard preparation, and record the peak responses as directed for Procedure: the resolution, R, between the peaks is not less than 1.6; the tailing factor for the benzyl alcohol peak and the internal standard peak is not greater than 3.5; and the relative standard deviation for replicate injections is not more than 3%.
Procedure Separately inject equal volumes (about 2 µL) of the Standard preparation and the Test preparation into the chromatograph, record the chromatograms, and measure the responses for the major peaks. [noteAfter six injections, raise the column temperature to about 300 for about 5 minutes, then cool to 100.] Calculate the percentage of benzyl alcohol in the Cream taken by the formula:
C(RU / RS),in which C is the concentration, in mg per mL, of benzyl alcohol in the Standard preparation; and RU and RS are the peak response ratios of the benzyl alcohol peak to the internal standard peak obtained from the Test preparation and the Standard preparation, respectively: between 90.0% and 110.0% of the claimed amount is present.
Ferrous sulfate solution Transfer 600 mg of ferrous sulfate to a 25-mL volumetric flask. Add 0.6 mL of glacial acetic acid, dilute with water to volume, and mix.
Standard preparation Dissolve an accurately weighed quantity of USP Ciclopirox Olamine RS in methanol to obtain a solution having a known concentration of about 0.2 mg per mL.
Assay preparation Transfer an accurately weighed quantity of Cream, equivalent to about 10 mg of ciclopirox olamine, to a 50-mL volumetric flask, add 25 mL of methanol, and shake by mechanical means for about 10 minutes. Dilute with methanol to volume, mix, centrifuge, and use the supernatant.
Procedure Transfer 4.0 mL of the Standard preparation, 4.0 mL of the Assay preparation, and 4.0 mL of methanol to provide a blank, to separate 25-mL volumetric flasks. Add 15 mL of methanol to each flask, and mix. Then to each flask add 1.0 mL of Ferrous sulfate solution, mix, dilute with methanol to volume, and mix. Store the flasks in the dark for 1 hour. Concomitantly determine the absorbances of the solutions from the Assay preparation and the Standard preparation against the blank in 1-cm cells at the wavelength of maximum absorbance at about 440 nm, with a suitable spectrophotometer. Calculate the quantity, in mg, of ciclopirox olamine (C12H17NO2·C2H7NO) in each g of the Cream taken by the formula:
50(C/W)(AU / AS)in which C is the concentration, in mg per mL, of USP Ciclopirox Olamine RS in the Standard preparation; W is the weight, in g, of Cream taken; and AU and AS are the absorbances of the solutions from the Assay preparation and the Standard preparation, respectively.
Auxiliary Information Please check for your question in the FAQs before contacting USP.Chromatographic Column
USP32NF27 Page 1931Pharmacopeial Forum: Volume No. 30(5) Page 1595
Chromatographic columns text is not derived from, and not part of, USP 32 or NF 27.