Ammonium Molybdate Injection
» Ammonium Molybdate Injection is a sterile solution of Ammonium Molybdate in Water for Injection. It contains not less than 85.0 percent and not more than 115.0 percent of the labeled amount of molybdenum (Mo).
Packaging and storage
Preserve in single-dose or multiple-dose containers, preferably of Type I or Type II glass.
Labeling
Label the Injection to indicate that it is to be diluted to the appropriate strength with Sterile Water for Injection or other suitable fluid prior to administration.
Identification
A:
The Assay preparation, prepared as directed in the Assay, exhibits an absorption maximum at about 313 nm when tested as directed for Procedure in the Assay.
B:
Add 0.3 mL of alkaline mercuric-potassium iodide TS to 5 mL of Injection: a reddish-brown color develops.
C:
Evaporate 50 mL of Injection on a steam bath to a volume of about 0.3 mL, and add 0.3 mL of ammonium hydroxide. Cool, and add slowly, with mixing, a well-cooled mixture of 1 mL of nitric acid and 1.2 mL of water. Allow to stand for 24 to 48 hours, and pass through a sintered-glass filter. To the filtrate add 0.5 mL of dibasic sodium phosphate TS: a yellow precipitate is formed, and it dissolves in an excess of 6 N ammonium hydroxide.
Pyrogen 151
It meets the requirements, the test dose being 10 mL of Injection per kg.
pH 791:
between 3.0 and 6.0.
Particulate matter 788:
meets the requirements for small-volume injections.
Other requirements
It meets the requirements under Injections 1.
Assay
Ammonium hydroxide diluent
Dilute 40 mL of ammonium hydroxide with water to 1000 mL. Store in a plastic bottle.
Sodium sulfate solution
Dissolve 1 g of sodium sulfate in water to make 100 mL.
Molybdenum stock solution
Transfer about 1.84 g of previously assayed Ammonium Molybdate, accurately weighed, to a 1000-mL volumetric flask, dilute with Ammonium hydroxide diluent to volume, and mix. This solution contains the equivalent of 1000 µg of molybdenum per mL.
Standard preparations
Transfer 0, 1.0, 2.0, 3.0, and 4.0 mL, respectively, of Molybdenum stock solution to separate 100-mL volumetric flasks, and to the respective flasks add 5.0, 4.0, 3.0, 2.0, and 1.0 mL of Ammonium hydroxide diluent. To each flask add 10 mL of Sodium sulfate solution, dilute with water to volume, and mix. These Standard preparations contain, respectively, 0, 10, 20, 30, and 40 µg of molybdenum per mL.
Assay preparation
Transfer an accurately measured volume of Injection, equivalent to about 500 µg of molybdenum, to a 25-mL volumetric flask, add 1.25 mL of Ammonium hydroxide diluent and 2.5 mL of Sodium sulfate solution, dilute with water to volume, and mix.
Procedure
Concomitantly determine the absorbances of the Standard preparations and the Assay preparation at the molybdenum emission line of 313.3 nm with a suitable atomic absorption spectrophotometer (see Spectrophotometry and Light-Scattering 851) equipped with a molybdenum hollow-cathode lamp and a nitrous oxideacetylene reducing flame, using water as the blank. Plot the absorbances of the Standard preparations versus concentration, in µg per mL, of molybdenum, and draw the straight line best fitting the five plotted points. From the graph so obtained, determine the concentration, in µg per mL, of molybdenum in the Assay preparation. Calculate the quantity, in µg, of molybdenum (Mo) in each mL of the Injection taken by the formula:
25C / V
in which C is the concentration, in µg per mL, of molybdenum in the Assay preparation; and V is the volume, in mL, of Injection taken.
Auxiliary Information
Please check for your question in the FAQs before contacting USP.
USP32NF27 Page 1536
|