4-Piperidinecarboxylic acid, 1-[2-(4-aminophenyl)ethyl]-4-phenyl-, ethyl ester, dihydrochloride.
Ethyl 1-(p-aminophenethyl)-4-phenylisonipecotate dihydrochloride [126-12-5].
» Anileridine Hydrochloride contains not less than 96.0 percent and not more than 102.0 percent of C22H28N2O2·2HCl, calculated on the dried basis.
Packaging and storage Preserve in tight, light-resistant containers.
B: Dissolve 50 mg in water in a 100-mL volumetric flask, dilute with water to volume, and mix (Stock solution). Transfer 4.0 mL of this solution to a 100-mL volumetric flask, and add 25 mL of pH 7.0 Buffer solution. (Prepare the pH 7.0 Buffer solution by dissolving 22.73 g of anhydrous dibasic sodium phosphate and 14.52 g of monobasic potassium phosphate in water to make 1000.0 mL. Dilute 25 mL of the buffer with water to 100 mL: the pH, determined potentiometrically, is 7.0 ± 0.05.) Dilute with water to volume, and mix (Solution A). Transfer 20.0 mL of the Stock solution to a 100-mL volumetric flask, add 25 mL of the pH 7.0 Buffer solution, dilute with water to volume, and mix (Solution B): the UV absorption spectrum of Solution A exhibits a maximum at 234 ± 1 nm, and the UV absorption spectrum of Solution B exhibits a maximum at 285 ± 2 nm.
C: To 5 mL of a solution (1 in 5000) add 2 mL of a 1 in 100 solution of p-dimethylaminobenzaldehyde in alcohol: a yellow color develops immediately.
D: A solution (1 in 100) responds to the tests for Chloride 191.
pH 791: between 2.5 and 3.0, in a solution (1 in 20).
Loss on drying 731 Dry it at a pressure below 5 mm of mercury at 100 for 2 hours: it loses not more than 1.0% of its weight.
Residue on ignition 281: not more than 0.1%.
Chloride content Dissolve about 200 mg, accurately weighed, in 50 mL of water in a glass-stoppered flask. Add 25.0 mL of 0.1 N silver nitrate VS, then add 5 mL of 2 N nitric acid and 5 mL of nitrobenzene, shake vigorously, add 2 mL of ferric ammonium sulfate TS, and titrate the excess silver nitrate with 0.1 N ammonium thiocyanate VS. Each mL of 0.1 N silver nitrate is equivalent to 3.545 mg of Cl: the content of Cl is between 16.0% and 17.2%.
Assay Dissolve about 200 mg of Anileridine Hydrochloride, accurately weighed, in 10 mL of glacial acetic acid by heating on a steam bath. Cool immediately in a cold water bath, add 5 mL of mercuric acetate TS, 20 mL of acetone, and 0.5 mL of indicator solution (70 mg of -naphtholbenzein, 10 mg of crystal violet, and 40 mg of quinaldine red in 100 mL of glacial acetic acid), and titrate with 0.1 N perchloric acid VS to a gray-green endpoint. Perform a blank determination, and make any necessary correction. Each mL of 0.1 N perchloric acid is equivalent to 21.27 mg of C22H28N2O2·2HCl.
Auxiliary Information Please check for your question in the FAQs before contacting USP.
USP32NF27 Page 1558